AUTONET TV

Steer Clear of Power Steering Problems (Power Steering Maintenance)

We usually take our vehicle's easy steering for granted until something goes wrong.  Power steering is what makes it almost effortless to turn the steering wheel, aiming your vehicle in the direction you want to go. Without the assistance of power from the engine, steering would be a laborious process, so you want to make sure the system is working well.

Power steering systems are usually one of two types, hydraulic and electric.  The hydraulic type uses a pump that is driven by either a belt or an electric motor.  This system uses hydraulic fluid to create pressure that gives your steering the power assist.  Since that pump is always working, time and distance traveled eventually take their toll, and these systems need to be periodically inspected.  Also, while that hydraulic fluid can last for years, it should be replaced periodically as it degrades over time. Your vehicle's owner's manual contains the manufacturer's recommendations.

A technician can check for leaks in the hoses, pump housing or reservoir.  Also, the belts should be inspected and so should the pump, as these can fail.  Signs of a failing pump are a groaning noise when you turn the steering wheel, stiff steering, squealing noises when you first start your car and puddles of a reddish-brown fluid under your vehicle. 

The other type is called EPS, or electric power steering, which is becoming more commonly used in the latest vehicles.  It only delivers power assist when you need it and has an electric motor that supplies that steering help.  It's more efficient, accurate, compact and clean. And because it has a lot fewer components, it's easier to maintain. 

If you have electric power steering, you may notice sometimes it's hard to turn the wheel or your Check Engine light comes on.  Sometimes the power assist motor fails or there can be problems with electrical connections.  Any time you have symptoms, it's important for your safety and that of drivers around you that you have a technician check them out.

Properly working brakes are essential for the safe operation of any vehicle.  Stop! And make sure yours are working properly.

Kingwood Service Center
3318 Northpark Dr
Kingwood, TX 77339
(281) 360-7323
http://www.kingwoodservicecenter.net

Kingwood Service Center Radiator Service

The coolant system is a vital part of your vehicle. It is also the second most common cause for vehicle failures. Even though coolant system failure is fairly common in Kingwood, it is easy to prevent.

The most recognizable part of the coolant system is the radiator. It is connected to the engine with hoses and is filled with coolant. The coolant draws heat off the engine and then passes into the radiator. Air passes through cooling fins to reduce the temperature of the coolant and then it's back to the engine again.

There are several ways for the cooling system to fail. Most common is with the coolant itself. Coolant is comprised of water and antifreeze. The proper ratio keeps the coolant from either boiling away or freezing. Understandably, either can lead to massive engine damage.

Another coolant issue that is often overlooked by Kingwood drivers is the age of the coolant itself. Antifreeze has additives that protect the coolant system from corrosion. As these additives are depleted over time, they can't protect the radiator and other parts from rust, scaling and corrosion. That old container of coolant gathering dust in your garage may still keep your engine cool, but it won't protect it from corrosion.

If you get a warning message to check the coolant or if the vehicle temperature gauge is in the hot zone, your cooling system needs to be checked. It's OK to add water or antifreeze yourself. But you need to be cautious. Remember four things:

• First, you never want to open the radiator pressure cap. You could be severely burned.
• Second, get to Kingwood Service Center in Kingwood immediately if your coolant is low. If that is not possible, follow the directions in your vehicle owners manual - it will direct you to only make additions to the coolant overflow bottle.
• Third, remember that you need a proper mixture of water and antifreeze. If you make an emergency addition to your cooling system, follow-up with your Kingwood Service Center service center where we can make necessary adjustments.
• Fourth, not all cars use the same type of antifreeze. You need to check your vehicle owners manual to make sure you use the right kind. Mixing antifreeze types or using the wrong kind of antifreeze may void the manufacturers warranty on your cooling system. Again, another reason to depend on your Kingwood Service Center service center in Kingwood to do things right.

Remember, Kingwood Service Center has the equipment to change your coolant quickly and inexpensively.

Kingwood Service Center
3318 Northpark Dr
Kingwood, TX 77339
(281) 360-7323
http://www.kingwoodservicecenter.net

See the Light (Automatic High Beam Dimmers)

It's happened to all of us.  We're driving down a highway at night and over a crest appears a car with its high beams blazing.  You are momentarily blinded, hoping the other driver will switch them to their low beam setting and restore your vision.

Not only do we not appreciate being blinded, face it; we don’t want to be that other driver, either.  You know, the one who forgets to turn down their high beams.

Why do we want high beams in the first place? They can improve safety when used correctly, giving drivers more reaction time since they can see farther down the road.  But research has found many drivers either don't use them or, when they do, they frequently forget to switch to low beams.  Enter the automatic high-beam dimmer.

The quest for the perfect one began back in the 1950s, General Motors invented something it called the "Autronic Eye." It was a phototube which sat on the dashboard and turned down your beams when it saw other headlights.  While touted as being the biggest advance in night driving safety in 30 years, it didn't work all that well.  But as technology got more advanced, systems improved.

Today's automatic high beam dimmers usually have a camera in the rear view mirror (pointing forward).  When the camera sees lights, software in the system's computer attempts to determine the source of the light, whether it is an oncoming vehicle, taillights, ambient city lights, street lights or the reflection off of a street sign.  It then adjusts the headlights to operate high beams if appropriate or a less-blinding mode if they’re not.

Some automakers are striving to make their headlight systems smarter and safer by developing lamps that can avoid blinding oncoming drivers by means other than simply dimming them. One idea? Splitting the beams so they will block just the portion that shines into the eyes of oncoming drivers.

It's a long way from the Autronic Eye. 

Kingwood Service Center
3318 Northpark Dr
Kingwood, TX 77339
(281) 360-7323
http://www.kingwoodservicecenter.net

Rear Window?Not the Movie! (Why Some Rear Windows Don't Go All the Way Down)

Alfred Hitchcock once made a mystery thriller film called "Rear Window." It had nothing to do with the rear window of today's cars, SUVs, CUVs and light trucks.  But there is one thing that some drivers DO find mysterious.  Why don't the rear windows in the second row of many of these vehicles go down all the way?

You've probably seen or owned one or two. That rear side window only goes down about a third, a half or three-quarters of the way. Yet there are some similar vehicles where the window goes down all the way.  What gives?

There was the rumor going around that the restriction on how far those windows could go down was a child safety feature.  The thought was that if those windows couldn't open up fully, a child (or pet) would be less likely to fall out.  But it turns out the real reason is that the way the rear doors were designed, there was just no room for the window to go down all the way into.

Many vehicles are configured so that the rear wheel arch continues into the rear door.  That arch restricts the space that would accommodate the window, so they had to stop the window somewhere higher than bottom of the door.

Seems buyers would prefer those back windows to go all the way down, so many manufacturers are changing designs to make that happen.  Longer vehicles can have their wheels pushed further back so the wheel arch isn't an issue.  Some have altered the position of the rear window track. 

If you have any questions about your rear side windows, you may want to consult your service advisor to check yours.  If they ARE supposed to go all the way down and they're not, it could be due to a few problems: corrosion, broken or bent window regulator components, electrical issues, etc. But if they're not supposed to go down all the way?  At least now you know for sure.

Kingwood Service Center
3318 Northpark Dr
Kingwood, TX 77339
(281) 360-7323
http://www.kingwoodservicecenter.net